Items: , Value:
Quick search:
Supertrux Catalogue
:
TRAIL-GEAR Products
Dual Transfer Case Crossmembers
If you have dual transfer cases on your Toyota Pickup or 4Runner you will want to protect them from trail damage with a crossmember that can take serious trail punishment. Trail-Gear's crossmembers are precision laser cut with slotted mounting holes for easy bolt on installation. Made from 3/8" thick plate steel with black powdercoat finish. Includes tapered bolts for a smooth bottom. Fits 1979-1995 Toyota Pickup and 4Runner with dual transfer case.
Some minor scratching of the powder coating may occur during shipping and handling.
Can be cut down to provide an excelent crossmember for a single transfer case.
Price Including Shipping:
£223.25
(Including: VAT at 17.5%)
Rear Springs
Trail-Gear leaf springs are flexible on the trail yet hold their lift year after year. Springs are pre cycled and lot tested to maintain quality. Nylon pads between the leafs reduce noise and allow springs to flex more easily. Raised clamp assemblies prevent binding of the leafs within the pack. Dual-pass shot-peened to relive material stress.
Our rear springs feature a full military wrap on the front and the 1/4 wrap on the rear. Spring rate is 235 lbs per inch. Leaf pack is 7 leaves plus a special torque leaf to reduce axle wrap. Springs are 56 5/8" long as measured along the top leaf. Pin to center of front mount is 27 1/2", pin to center of rear mount is 29 5/8". New polly bushings are included with springs. These springs are longer than stock and will require hanger relocation.
Price Including Shipping:
£293.75
(Including: VAT at 17.5%)
Front Springs
Trail-Gear leaf springs are flexible on the trail yet hold their lift year after year. Springs are pre cycled and lot tested to maintain quality. Nylon pads between the leafs reduce noise and allow springs to flex more easily. Raised clamp assemblies prevent binding of the leafs within the pack. Dual-pass shot-peened to relive material stress.
Our front springs feature a full military wrap on the front and the 1/4 wrap on the rear. Spring rate is 220 lbs per inch. Leaf pack is 6 leaves. Springs are 47" long as measured along the top leaf. Pin to center of front mount is 22" and pin to center of the shackle mount is 25". New polly bushings and left side spring pad are included with springs.
Now our front 5" springs are available in a heavy-duty version with a 25% higher spring rate. We have added a 7th leaf and readjusted the length of the leaves to match. If you are running a larger v6 or v8 motor you will appreciate the extra weight carrying capacity of these springs.
Price Including Shipping:
£293.75
(Including: VAT at 17.5%)
U-Bolt Flip Kit
U-bolt flip kits help increase ground clearance under your rig. Stock u-bolts face down and offer a snag point for rock and trail debris. Our u-bolt flip kit point the spring bolt up and out of harm way. This results in better ground clearance and less damage to the thread section of the bolt.
Each kit contains two flip plates and four 9/16" bolts with nuts and washers. Front kits will accommodate spring packs up to 2" thick. Rear kit will accommodate spring packs up to 2.5" thick. Crossover steering required for installation of flip kit. Unpainted finish.
Price Including Shipping:
£58.75
(Including: VAT at 17.5%)
Spring Hanger Kit
Our Solid Axle Hanger kit contains
Front offset hanger w/ gussets
Greasable shackles
Frame tubes
Tube jigs
Hanger kit allows of hanging of leaf springs on 1986-1995 Toyota Pickups and 4Runners. Kit designed to work with many 3" - 6" lift aftermarket springs.
Frame jigs make it easy to place shackle tubes in your frame. To install, place jigs on frame under the cab body mount. Mark the frame, and cut frame tube holes with torch. Slide tubes in place and weld in. Clamp front hanger in place and weld. Bolt on springs with included bushings and shackles.
Price Including Shipping:
£176.25
(Including: VAT at 17.5%)
Rock Sliders - Rocker Protection
Rock Sliders are a great way of protecting the rocker panels of your Toyota pickup or 4Runner. Heavy duty design can take a pounding from the rocks while keeping body damage to a minimum. Strong enough to take the entire weight of the truck. A high-lift jack can be used anywhere along it's length for repositioning of rig or axle servicing. Sold in pairs. Made from 1 3/4" X .120 round HREW tubing. Bars come with the outer section welded but the legs are not attached. Legs are pre-notched and can be be cut to length to allow for different mounting positions.
Price Including Shipping:
£170.38
(Including: VAT at 17.5%)
Master Cylinder - 1" Bore
Makes a great replacement for older Pickup's and 4Runners with smaller bore size. Fits 1979-1995 Pickups and 4Runners. Master Cylinder features 1" piston and residual valves for both front and rear disc brakes. Can be used with disc or drum brakes. Includes reservoir.
Price Including Shipping:
£151.58
(Including: VAT at 17.5%)
Supertrux Catalogue
:
TRAIL-GEAR Products
4x4 Suspension & 4x4 Accessories Specialist - L.A.Supertrux - Daventry, Northamptonshire, England
